View SIL4_790157.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SRC
DEVICES
SPECIFICATIONS
SIP SERIES REED RELAYS
SIL4 DSS4 MVS4 MSS4
MVS4 Mercury-Wetted Reed Relays
All parameters at 25C unless otherwise stated. PARAMETER CONDITIONS Max DC/PeakAC Resistive Max DC/PeakAC Resistive Max DC/PeakAC Resistive Max DC/PeakAC Resistive Signal Level 1.0V 10mA 50V, 1A 500V, 100mA Rated Loads(2) 50mV, 10mA SYMBOL VL IL IC CR High Power/Reliability Position-Sensitive(3) Hg-Wetted MIN TYP 1000 2 50 7 Hg 40 MAX 1000(1) 2 3 50(4) 100 -
MSS4
Non-Position-Sensitive Hg-Wetted MIN TYP 200 7 Hg 16 MAX 500 2 3 50 100 UNITS Volts Amps Amps Watts x106 Ops x106 Ops x106 Ops x106 Ops m mgram
Contact Ratings
Switching Voltage Switching Current Carry Current Contact Rating Life Expectancy
Static Contact Resistance Contact Material Hg Content
Relay Specifications
Insulation Resistance Capacitance Between all isolated pins at 100V, 25C, 40% RH Across Open Contacts Upper Contact to Coil Closed Contact to Coil Between Contacts Contacts to Coil At Nominal Coil Voltage 10Hz Square Wave Zener-Diode Suppression IR I/O I/O TOP TREL 1010 2000 2500 1012 0.8 2.2 3.3 2.5 2.5 108 2000 1400 1010 2 4 1.75 1.5 pF pF pF VDC/Peak AC VDC/Peak AC ms ms
Dielectric Strength Operate Time, no bounce Release Time
Environmental Ratings
Storage Temperature Operating Temperature Soldering Temperature Vibration Resistance (Survival) Shock Resistance (Survival) Weight
(1) (2)
T T Applied to pins,10 sec. max. 10Hz - 500Hz 111ms, 1/2 Sine Wave
A O
G S -
-40 -38 -
2.2
+105 +85 +260 10 30 -
-40 -38 -
2.4
+105 +75 +260 10 30 -
C C C Gs Gs grams
Current limited up to 5mA, typical 20 million operations; for further life information, consult factory. Refer to MH4 (MVS4) & MYAD (MSS4) life graphs. (3) Vertical mounting required. Pin #1 is up. (4) Derate to 5 watts when switching voltages >500V.
USA 1-866-SRC-8668 Europe 32-89-328850
Far East 886-2-2698-8422
www.srcdevices.com
3
SIP SERIES REED RELAYS
SIL4 DSS4 MVS4 MSS4
COIL SPECIFICATIONS
Contact Form Units Conditions Part # 1-Form-A 1-Form-A 1-Form-A 1-Form-A 1-Form-B 1-Form-B 1-Form-B 1-Form-A 1-Form-A 1-Form-A 1-Form-B 1-Form-B 1-Form-B 1-Form-A 1-Form-A 1-Form-A 1-Form-A 1-Form-A 1-Form-A Min Typ 3 5 12 24 5 12 24 5 12 24 5 12 24 5 12 24 5 12 24 Max 6 10 16 30 6 14 29 10 16 30 10 16 30 7 15 30 10 16 30 Coil Voltage Volts Coil Resistance +/- 10% (25C) Min 135 450 900 1800 450 900 1800 450 900 1800 450 900 1935 94.5 450 1935 126 450 1935 Typ 150 500 1000 2000 500 1000 2000 500 1000 2000 500 1000 2150 105 500 2150 140 500 2150 Max 165 550 1100 2200 550 1100 2200 550 1100 2200 550 1100 2365 116 550 2365 154 550 2365 Operate Voltage Volts
SRC
Release Voltage Volts
DEVICES
Nominal Input Power mW
Must operate by (25C) Must release by (25C) Min Typ Max 2.25 3.75 8.6 17.5 3.75 9 18 3.75 8.6 17.5 3.75 9 18 3.75 9 18 3.75 9 18 Min 0.3 0.4 1.5 2.5 0.8 1.5 2.5 0.8 1.5 2.5 0.8 1 2 0.5 1 2.0 0.5 1 2 DIMENSIONS mm (inches)
0.49 (0.019) 5.08 (0.200) 15.24 (0.600) 3 3.20 0.25 (0.125 0.010) 6.70 MAX. (0.264) 8.20 MAX. (0.323) 1 Top View
Typ
Max
Min
Typ 60 50 144 288 50 144 288 50 144 288 50 144 268 238 288 268 179 288 268
Max
SIL41A03(B) SIL41A05(B) SIL41A12(B) SIL41A24(B) SIL41B05(B) SIL41B12(B) SIL41B24(B) DSS41A05 DSS41A12 DSS41A24 DSS41B05 DSS41B12 DSS41B24 MVS41A05(B) MVS41A12(B) MVS41A24(B) MSS41A05 MSS41A12 MSS41A24
MECHANICAL DIMENSIONS
SIL4/DSS4
3.18 (0.125) 0.49 (0.019) 19.05 MAX. (0.750) 5.08 (0.200) 3 5.08 MAX. (0.200) 15.24 (0.600) 1 Top View 7 5
19.05 MAX. (0.750)
MVS4/MSS4
7 5
2.54 REF. 7.62 MAX. (0.100) 0.41 REF. (0.300) Mold mark denotes pin 1 side (0.016) of relay 2.00 REF. (0.080)
SIL4/DSS4 Pinout
Form A 7 Form B
MVS4/MSS4 Pinout
7
7 5 3 1 Top View
0.33 (0.013)
5 3 1 Top View
0.33 (0.013)
5 * 3 1 Top View * MVS4 only must be mounted vertically with pin #1 up. UP
For Form B or diode options, coil polarity (pin #3 positive) must be observed.
USA 1-866-SRC-8668 Europe 32-89-328850
Far East 886-2-2698-8422
www.srcdevices.com
4
SRC
DEVICES
SIL4/DSS4 Rated Load: 5VA
99.9 50.0 30.0 20.0 10.0 5.0 3.0 2.0 1.0 0.5 0.3 0.2 0.1 0.1 1.0 2 1 0 % Cumm. Fail -1 -2 48V-100mA Load 0.935 x 10 ops 90% Survival 6 2.576 x 10 ops MTBF
6
SIP SERIES REED RELAYS
SIL4 DSS4 MVS4 MSS4
PERFORMANCE GRAPHS
SIL4/DSS4 Rated Load: 10VA
99.9 50.0 30.0 20.0 10.0 5.0 3.0 2.0 1.0 0.5 0.3 0.2 0.1 0.1 1.0 2 1 0 20V-500mA Load 6 1.290 x 10 ops 90% Survival 6 5.978 x 10 ops MTBF 50V-200mA Load 0.317 x 10 ops 90% Survival 6 0.671 x 10 ops MTBF
6
% Cumm. Fail
-1 -2 -3 -4 -5 -6
-3 -4 -5 -6
10V-500mA Load 4.064 x 10 ops 90% Survival 6 12.838 x 10 ops MTBF
6
10.0
-7 100.0
100V-100mA Load 0.763 x 10 ops 90% Survival 6 3.919 x 10 ops MTBF
6
10.0
6
-7 100.0
Number of Operations (x106)
Number of Operations (x10 )
MVS Series Rated Load: 50VA-20Hz
99.9 2 1 0 -1 -2 50V-1A Load 3.897 x 106 ops 90% Survival 15.520 x 106 Ops MTBF -3 -4 -5 -6 0.1 1.0 10.0 -7 100.0 50.0 30.0 20.0 10.0 5.0 3.0 2.0 1.0 0.5 0.3 0.2 0.1
% Cumm. Failures
Number of Operations (x106)
Relay Internal Temperature Rise vs. Power
50 Delta T (C) of Relay 40 30 20 10 0
SIL4/DSS4 Relay Temperature Rise vs. Coil Power (5V)
Delta T ( C) of Relay 0 25 50 75 100 125 150 175 200
MVS4 Relay Temperature Rise vs. Coil Power (1-Form-A 5V)
100 80 60 40 20 0 0 75 150 225 300 375 450 525 600 675 750 Coil Input Power (mW)
Coil Input Power (mW)
USA 1-866-SRC-8668 Europe 32-89-328850
Far East 886-2-2698-8422
www.srcdevices.com
5
SIP SERIES REED RELAYS
SIL4 DSS4 MVS4 MSS4
PERFORMANCE GRAPHS
Pull In/Drop Out vs. Temperature
MVS4/MSS4 Pull In/Drop Out vs. Temperature
SRC
DEVICES
30 20 % Change 10 0 -10 -20 -30 -40
-20
0
20
40
60
80
100
Ambient Temperature (C)
Operate/Release Time Characteristics
SIL4/DSS4 Timing vs. Frequency
250 2000 200 Operate Timing (s)
Timing (s)
SIL4/DSS4 Operate/Release Time vs Overdrive (Diode Suppression)
200 Release Timing (s) Release Timing (s) MAX 1500 MIN 1000 Operate Timing Release Timing MAX MIN 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 100 150
150 100 50 0 0 50 100 150
Operate Timing Release Timing
500
50
200
250
300
0 Times Nominal Coil Drive
0
Frequency (Hz)
SIL4/DSS4 Operate/Release Time vs. Overdrive (No Diode Suppression)
2000
Operate Timing (s)
SIL4/DSS4 Operate/Release Time vs. Overdrive (Diode & Zener Suppression)
200
Release Timing (s)
2000 Operate Timing (s)
200
1500
150
1500 Operate Timing Release Timing 1000 MAX MIN MAX MIN 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5
150
1000 Operate Timing Release Timing MAX MIN 0 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 Times Nominal Coil Drive
100
100
500
50
500
50
0
0 Times Nominal Coil Drive
0
USA 1-866-SRC-8668 Europe 32-89-328850
Far East 886-2-2698-8422
www.srcdevices.com
6
SRC
DEVICES
SIP SERIES REED RELAYS
SIL4 DSS4 MVS4 MSS4
MAGNETIC INTERFERENCE
If relays are inserted in close proximity, the pickup and dropout voltages will be affected by the magnetic flux produced when the coils are energized. In general, worst-case magnetic interaction conditions for pull-in voltage in a matrix exist when all relay fields have the same polarity and all of the fields are from adjacent relays (See figure). The direction of the parameter shift is determined by whether the stray flux aids or bucks the flux produced by the coil of the relay under consideration. To calculate the change in pull-in voltage and dropout voltage, multiply the percent change shown by the relay's nominal voltage. For example, if the percent change in pull-in voltage is 14% for a 5V nominal relay, the pull-in voltage will increase by 0.7 volts.
SIL4/DSS4 Magnetic Interference
20.0% % Increase of P.I. and D.O. Relay under test Adjacent Relays 15.0% % P.I. and D.O. Increase 10.0%
MVS4/MSS4 Magnetic Interference
Relay under test Adjacent Relays 7.5%
10.0%
x
x
5.0%
x
x
5.0%
0.0%
1. Nominal voltage is applied to the adjacent relays. 2. The % increase of pull-in and drop out of the relay under test is measured and compared with the values without any magnetic influence of adjacent relays.
2.5%
0.0% 0.7
1. Nominal voltage is applied to the adjacent relays. 2. The % increase of pull-in and drop out of the relay under test is measured and compared with the values without any magnetic influence of adjacent relays.
0.1
0.2
0.3
0.4
0.5
0.6
0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 0.7 Distance Between Centers of Adjacent Relays (in inches)
Distance Between Centers of Adjacent Relays (x, in inches)
ORDERING INFORMATION
A complete part number is represented by the digits below.
XXXX XX XX X
Series
SIL4 DSS4 Blank = No diode B = Diode option (SIL4 & DSS4)
Coil voltage Contact Form
1A = 1-Form-A (Normally open) 1B = 1-Form-B (Normally closed) 03 = 3V (SIL4) 05 = 5V 12 = 12V 24 = 24V
USA 1-866-SRC-8668 Europe 32-89-328850
Far East 886-2-2698-8422
www.srcdevices.com
7

▲Up To Search▲

Price & Availability of SIL4

	To Download SIL4 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .